Polímeros: Ciência e Tecnologia
https://www.revistapolimeros.org.br/article/doi/10.4322/polimeros.2013.040
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Efeito da Montmorilonita Organifílica na Compatibilização e nas Propriedades Morfológicas, Mecânicas e Térmicas de Blendas de PA6/ PEBD

The effect of organophilic montmorillonite on compatibilization, morphology and mechanical and thermal properties of PA6/ LDPE blends

Coelho, Paulo H. S.; Morales, Ana R.

Downloads: 0
Views: 1155

Resumo

Blendas imiscíveis de poliamida 6 e polietileno de baixa densidade foram preparadas com e sem a presença de polietileno enxertado com anidrido maleico como compatibilizante. Montmorilonita organofílica foi incorporada nas blendas por intercalação do fundido. Análises morfológicas e estruturais apresentaram boa dispersão da argila, com a obtenção de estruturas intercaladas e esfoliadas. A separação de fases foi observada nas amostras, e tanto o compatibilizante como a argila causaram redução no tamanho dos domínios. Esta estrutura proporcionou uma melhora significativa nas propriedades mecânicas das blendas, revelando o efeito de reforço causado pela argila. O módulo elástico e a tensão máxima aumentaram em até 300% e 100%, respectivamente. O efeito da compatibilização da argila foi positivo. Pelas análises de DSC pode-se observar o surgimento de um pico na região de fusão da PA6 atribuído à formação de uma nova fase cristalina devido à presença de argila.

Palavras-chave

Nanocompósitos, blendas, montmorilonita, polietileno, poliamida

Abstract

Immiscible blends of polyamide 6 and low density polyethylene were prepared with and without maleic anhydride grafted polyethylene used as a compatibilizer. Organophilic montmorillonite was incorporated in the blends by melt intercalation. Morphological and structural analysis showed good clay dispersion with partially exfoliated and intercalated structures. Phase separation was observed and domains size reduction was induced by the clay and the compatibilizer. Improvement on mechanical properties of compounds was observed, showing the reinforcing effect caused by the clay. Elastic modulus and tensile strength have increased up to 300% and 100%, respectively. The clay showed a positive effect on compatibilization. DSC analysis revealed a new melting peak for the PA6 that should be associated to a new crystalline phase due the clay effect. Immiscible blends of polyamide 6 and low density polyethylene were prepared with and without maleic anhydride grafted polyethylene used as a compatibilizer. Organophilic montmorillonite was incorporated in the blends by melt intercalation. Morphological and structural analysis showed good clay dispersion with partially exfoliated and intercalated structures. Phase separation was observed and domains size reduction was induced by the clay and the compatibilizer. Improvement on mechanical properties of compounds was observed, showing the reinforcing effect caused by the clay. Elastic modulus and tensile strength have increased up to 300% and 100%, respectively. The clay showed a positive effect on compatibilization. DSC analysis revealed a new melting peak for the PA6 that should be associated to a new crystalline phase due the clay effect.

Keywords

Nanocomposites, blends, montmorillonite, polyethylene, polyamide

References

1. Wang, L.; Xie, X.; Su, S.; Feng, J. & Wilkie, C. A. - Polym. Degrad. Stab., 95, p. 572 (2010).

2. Mishra, S.; Sonawane, S. S., Shimpi, N. G.; Mishra, S.; Sonawane, S. S. & Shimpi, N. G. - Appl. Clay Sci., 46, p. 222 (2009).

3. Livi, S.; Jannick, D. -R.; Pham, T. N. & Gérard, J. -F. - J. Colloid Interface Sci., 354, p. 555 (2011).

4. Paiva, L. B. & Morales, A. R. - Polímeros, 16, p. 136 (2006).

5. Wang, J.; Du, X. ; Yu, H.; Jiang, Z.; Liu, J. & Tang, T. - Polymer, 50, p. 5794 (2009).

6. Vassiliou, A. A.; Chrissafis, K. & Bikiaris, D. N. - Thermochim. Acta, 500, p. 21 (2010).

7. Rodolfo, Jr., A. & Mei, L. H. I. - Polímeros, 19, p. 1 (2009).

8. Motamedi, P. & Bagheri, R. - Mater. Des., 31, p. 1776 (2010).

9. Dintcheva, N. Tz.; Filippone, G.; La Mantia, F. P. & Acierno, D. - Polym. Degrad. Stab., 95, p. 527 (2010).

10. Dayma, N.; Satapathy, B. K. - Mater. Des., 33, p. 510 (2012).

11. Medeiros, V. N.; Araújo, E. M.; Maia, L. F.; Pereira, O. D. & Arimateia, R. R. - Polímeros, 18, p. 302 (2008).

12. Morales, A. R.; Cruz, C. V. M. & Peres, L. - Polímeros, 20, p. 39 (2010).

13. Agrawal, P.; Araújo, E. M. & Mélo, T. J. A. - Polímeros, 21, p. 383 (2011).

14. Ray, S. S. & Bousmina, M. - Macromol. Rapid. Commun., 26, p. 1639 (2005).

15. Scaffaro, R; Mistretta, M.C. & La Mantia, F.P.; Polym. Degrad. Stab., 93, p. 1267 (2008).

16. González-Nuñez, R.; Padilla, H.; De Kee, D. & Favis, B. D. - Polym. Bull., 46, p. 323 (2001).

17. Yordanov, Chr. & Minkova, L. - Eur. Polym. J., 39, p. 951 (2003).

18. Yordanov, Chr. & Minkova, L. - Eur. Polym. J., 41, p. 527 (2005).

19. Lahor, A.; Nithitanakul, M. & Grady, B. P. - Eur. Polym. J., 40, p. 2409 (2004).

20. Filippi, S.; Yordanov, Chr.; Minkova, L.; Polacco, G. & Talarico, M.; Macromol. Mater. Eng., 289, p. 512 (2004).

21. Jiang, C.; Fillipi, S. & Magagnini, P - Polymer, 44, p. 2411 (2003).

22. Kusmono, W. S.; Mohd Ishak, Z. A.; Chow, W. S.; Takeichi, T.; Rochmadi - Polym. Lett., 2, p. 655 (2008).

23. http://www.nanocor.com/tech_sheets/N604.pdf, acessada em Maio de 2011.

24. Yan, L. -T. & Sheng J. - Polymer, 47, p. 2894 (2006).

25. Shi, D.; Hu, G. -H.; Ke, Z.; Li, R. K. Y. & Yin, J. - Polymer, 47, p. 4659 (2006).

26. Ray, S.S.; Pouliot, S. & Bousmina, M. - Macromol. Rapid. Commun., 26, p. 450 (2005).

27. Si, M.; Araki, T.; Ade, H.; Kilcoyne, A. L. D.; Fisher, R.; Sokolov, J. C. & Rafailovich, M. H. - Macromolecules, 39, p. 4793 (2006).

28. Hong, J. S.; Namkung, H.; Ahn, K. H.; Lee, S. J. & Kim, C. - Polymer, 47, p. 3967 (2006).

29. Mehta, S.; Mirabella, F. M.; Rufener, K. & Bafna, A. - J. Appl. Polym. Sci., 92, p. 928 (2004).

30. Hotta, S. & Paul, D. R - Polymer, 45, p. 7639.

31. Spencer, M. W.; Cui, L., Yoo, Y & Paul, D.R. - Polymer, 51, p. 1056 (2010).

32. Morawiec, J.; Pawlak, A.; Slouf, M.; Galeski, A.; Piornowska, E. & Krasnikowa, N. - Eur. Polym. J., 41, p. 1115 (2005).

33. Psarski, M.; Pracella, M. & Galeski, A. - Polymer, 41, p. 4923 (2000).

34. Chiu, F. C.; Lai, S. M.; Chen, Y. L. & Lee, T.H. - Polymer, 46, p. 11600 (2005).

35. Tung, J.; Simon, G. P. & Edward, G. H. - Polym. Eng. Sci., 45, p. 1606 (2005).

36. Lincoln, D. M.; Vaia, R. A.; Wang, Z.-G.; Hsiao, B. S. & Krishnamoorti, R. - Polymer, 42, p. 1621 (2001).

5883718b7f8c9d0a0c8b4953 polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections